ກ່ຽວກັບຫຼັກການ deceleration ຂອງ extruder screw ຄູ່

Ningbo Fangli Technology Co., Ltd. ເປັນຜູ້ຜະລິດອຸປະກອນກົນຈັກທີ່ມີປະສົບການເກືອບ 30 ປີອຸປະກອນ extrusion ທໍ່ພາດສະຕິກ, ການປົກປັກຮັກສາສິ່ງແວດລ້ອມໃຫມ່ແລະອຸປະກອນວັດສະດຸໃຫມ່. ນັບຕັ້ງແຕ່ການສ້າງຕັ້ງ Fangli ໄດ້ຖືກພັດທະນາໂດຍອີງໃສ່ຄວາມຕ້ອງການຂອງຜູ້ໃຊ້. ໂດຍຜ່ານການປັບປຸງຢ່າງຕໍ່ເນື່ອງ, R&D ເອກະລາດກ່ຽວກັບເຕັກໂນໂລຢີຫຼັກແລະການຍ່ອຍອາຫານແລະການດູດຊຶມຂອງເຕັກໂນໂລຢີທີ່ກ້າວຫນ້າແລະວິທີການອື່ນໆ, ພວກເຮົາໄດ້ພັດທະນາ.ທໍ່ PVC ສາຍ extrusion, PP-R ທໍ່ extrusion line, ການສະຫນອງນ້ໍາ PE / ທໍ່ອາຍແກັສ extrusion line, ເຊິ່ງໄດ້ຖືກແນະນໍາໂດຍກະຊວງກໍ່ສ້າງຂອງຈີນເພື່ອທົດແທນຜະລິດຕະພັນທີ່ນໍາເຂົ້າ. ພວກ​ເຮົາ​ໄດ້​ຮັບ​ຫົວ​ຂໍ້​ຂອງ "ເຄື່ອງ​ຫມາຍ​ອັນ​ດັບ​ຫນຶ່ງ​ໃນ​ແຂວງ Zhejiang​"​.

In most extruders, the change of screw speed is realized by adjusting the motor speed. The driving motor usually rotates at full speed of about 1750 rpm, which is too fast for an extruder screw. If it rotates at such a fast speed, too much friction heat will be generated, and the uniform and well stirred melt cannot be prepared due to the short residence time of the plastic. The typical reduction ratio should be between 10:1 and 20:1. In the first stage, both gears and pulley blocks can be used, but in the second stage, it is best to use gears and position the screw in the center of the last big gear. For some slow-moving machines (such as twin-screw for UPVC), there may be three deceleration stages, and the maximum speed may be as low as 30 rpm or less (ratio up to 60:1). On the other hand, some very long twin screws for stirring can run at 600 rpm or faster, so a very low deceleration rate and more deep cooling are required.

ຖ້າທ່ານຕ້ອງການຂໍ້ມູນເພີ່ມເຕີມ, Ningbo Fangli Technology Co., Ltd. ຍິນດີຕ້ອນຮັບທ່ານຕິດຕໍ່ສອບຖາມລາຍລະອຽດ, ພວກເຮົາຈະໃຫ້ຄໍາແນະນໍາດ້ານວິຊາການມືອາຊີບຫຼືຄໍາແນະນໍາການຈັດຊື້ອຸປະກອນ.